FULL CYCLE AUTOMATION

          4 zone control from a single Master Unit. Diagram above represents just a single zone!

Free Worldwide Shipping!!! Applies to our full range of products

For bulk pricing please contact us

 

The Mydro Lab System is the only system on the market that provides FULL CYCLE AUTOMATION. Read on to better understand the significance of this.

The Mydro Lab System is a multi-zone climate and reservoir controller kit that is worldwide compatible (90V to 250V). Backed by a 4 year warranty the Mydro Lab Master Unit provides top level automation of up to 4 zones, greatly outperforming other systems that cost over $7000. Not merely providing nutrient and pH maintenance dosing (like other expensive systems are limited to) but also going much further to provide FULL CYCLE automation. This means fully automatic reservoir change outs and refills with auto stirring/mixing and fresh reservoir preparations on a user set schedule and custom nutrient/additive regiment with up to 10 dosing pumps per reservoir. The system has user selectable modes for Run to Waste, Flood and Drain, Aeroponics ect. You can monitor and control everything wirelessly. It is very easy to setup and use the system. The wireless user interface is designed for simplicity with few buttons and intuitive menus for changing settings.

Purchase only what you need. For example if you just want the Climate Control then you can purchase that along with the Master Unit. You can then buy the Reservoir Unit at a later stage. Or do it vice versa. And of course there’s the Multi Doser, Expansion Pack and pH Doser that you can also purchase separately to add to your system.
And remember you can buy multiple units for up to 4 zone control from a single Master Unit. That’s 4 separate grow rooms and 4 separate reservoirs with 10 dosing pumps per reservoir. Each zone is represented by the diagram above which demonstrates the high level of automation you will have on each and every zone. Our system is the only device you’ll ever need to monitor and control every piece of equipment you own. Whether you’re a total beginner or a long time pro with the most complex setup, Mydro Lab is all you’ll ever need. Say goodbye to annoying timers, thermometers, hand held pH and EC probes, mechanical float systems, and say goodbye to hours of work every week. Everything you need is done wirelessly via the super simple 5 button interface on the Master Unit.

We use high quality components in our products as well as quality industrial level probes. As such we offer a 3 year “Super” Warranty on all units. We call it a “Super” Warranty because there’s no warranty label to maintain and no unfair catches. You are covered for ALL parts and labour.

If you have any trouble setting up, you can return it for a full refund including postage. But that’s not likely since it’s not difficult to set up. You can of course contact us for assistance and we will be happy to help. Since your unit will be covered by our 3 year warranty, if you have any issues at all with the unit in the first 3 years, you can send it back to have the unit repaired or refurbished. If we can’t fix the issue immediately we will send you a brand new unit instead. Our warranty covers all parts and labour. Note that we don’t use a warranty label since this only serves to void your warranty. We want your warranty to be guaranteed for 3 years. Note that for warranty claims you just need to pay the postage to send it to us. We will repair/refurbrish/replace it and then we pay the postage to send it back to you. We also offer after warranty services. For example you could send in a 10 year old unit to be refurbished for much less than the cost of a new unit. Then you’ll be set for many more years to come!

The Mydro Lab provides TOTAL reservoir automation. Besting even the top end systems that cost a fortune.

       Reservoir Control Features:

• Fully Autonomous Complete Cycle Operation

• Nutrient and pH up & down dosing

• 10 dosing pumps per reservoir with up to 4 reservoirs (any nutrient line including powders!)

• Automatic reservoir change, top up, refill, preparation & maintenance

• Designed for run to waste and recirculating including flood & drain, DWC and aeroponics (selectable grow mode)

• Mix/Stir Pump control (Thus no need to use sample pot!)

• 4 zone control (diagram above represents just a single zone!)

• User selectable grow modes, reservoir size, dosing parameters ect.

• Feed Pump control with clock scheduling, day mode and cycle mode

• Water temperature control with heater/chiller

• Degrees Celcius/Farenheit, EC/PPM, Litres/Gallons

  .

  Climate Control Features:

• Displays electricity consumption in dollars and cents

• CO2 fuzzy logic with photo and clock schedule modes

• Optional night time exhaust for sealed rooms

• Temperature & Humidity with dead-band

• Independent Day & Night Settings

• User selectable grow modes for sealed room with CO2, vented room ect.

• Intelligent vent+AC control mode

• Intelligent CO2 with vent fan control mode

• 2 way humidity control (dehum & hum)

• 3 way temperature control (AC, vent & heat)

• Lighting Control with clock schedule or custom cycle

• Cycle timer control for wall fans ect.

• Degrees Celcius/Farenheit

.
No other controller on the market comes close to providing this level of automation and flexibility.

With other controller systems you can spend over $10 000 and you’ll still be doing manual reservoir changes then adding nutrients by hand. Other high end controllers will merely maintain the reservoir once prepared. Our system intelligently takes care of the entire process so that it can continue working through cycle after cycle for continuous automation. This means far less work for the user. All this manual work is taken care of in a very reliable way, significantly more reliable than a human being in our experience.

The system can be set to Auto or Regular mode. Auto mode being a fully automatic mode whereby for recirculating systems you select how often you want the reservoir to be changed. For drain to waste systems the reservoir is automatically refilled after it’s been consumed. Once the reservoir change/refill is complete the system will set the desired temperature, prepare it with your custom line up of nutrients and additives then set the desired pH. Then it will maintain the reservoir based on your desired PH and EC setpoints.

In regular mode you simply instruct the system to perform each step. For example when you want to perform a reservoir change it is just a matter of instructing the system to do so via the wireless Master Unit. And so forth for all the other steps involved in running a reservoir system. It’s all just a few button presses away.

The climate control features of the system are equally impressive. There is a grow mode for each type of setup. For example if you have CO2 with an AC you will use the “AC Sealed” mode. If you have no CO2 but have an AC and an exhaust fan you could choose “Fan+AC(Smart)” mode or you could choose some of the other options. If you have CO2 and no AC but you do have an exhaust fan you would choose “SmartFan+CO2” mode in order to avoid exhausting CO2 away from your garden.

The system provides wireless monitoring & control of light schedule, air temp, RH, CO2, with custom dead zones and separate day/night settings. The CO2 controller is second to none. It can use the built in light sensor to only function during the lights on period and it can also run on a custom clock schedule. It has fuzzy logic mode, regular mode, and burner mode with high temp safety shutoff. It offers custom set point with dead zone and optional night time exhaust with night time CO2 level control via exhaust fan.

You can also set your AC or heater to only work during certain hours if you like. The ability to customize is huge. Perhaps one of the nicest climate control features is the ability to intelligently decide between using vent fans or air conditioning. For example when it’s hot out you may need your AC but when it’s cold the exhaust fan might do the job. Rather than you having to keep changing things manually, just plug everything in to the Mydro Lab Climate Controller and let the system intelligently decide. Without any need for an outside temperature sensor.

…and it’s super easy to set up (Plug & Play):

The Mydro Lab System has universal power sockets for the following equipment: Exhaust/Intake fans, AC, heater, CO2 burner/reg+tank, dehumidifier, humidifier/fogger, grow lights, feed pump, fill pump, drain pump, mixing pump, water heater/cooler. But if you don’t own all that equipment no worries just plug in what you have. The system will let you make optimal use of the equipment you have. Out of the box the unit comes with the following settings:

Day: 27.3C air temp, 50%RH, 1200ppm CO2, 
          19.8C water temp, 5.8pH, 2.0EC

Night: 26.5C air temp, 50%RH, CO2 Off,
             19.8C water temp, 5.8pH, 2.0EC

Feed Schedule: 2 waters per day @ 20 seconds each only during lights on
Light Schedule: 12 hrs on/12hrs off, with lights coming on at 8:30pm.

All of the above settings can be changed via the master controller. However if you wish to go for a cheaper option you can purchase just the Climate controller or Reservoir Controller without the Master Unit. It means you won’t have the ability to monitor or change any settings but you can still run a garden with these stock settings. You always have the option of buying the Master Unit later by its self to enable wireless monitoring and control over all of your settings and preferences.